Questions & discussions of garage door operator problems and solutions.

Latest topics

» Sensor problem?
Fri Dec 15, 2017 10:07 pm by AndyB

» New Garage Door Controller, Good to Invest?
Thu Dec 14, 2017 10:13 pm by liang916

» Raynor 2265RGD Intermittent Problem Opening Door
Fri Dec 08, 2017 2:15 am by bankercop

» Compatible remote (2 doors) and keyless entry for Raynor 110-7?
Wed Dec 06, 2017 1:43 am by GDZone

» Quirky GDO
Tue Dec 05, 2017 11:32 am by GDZone

» Chamberland Safety sensors on am stanley vemco
Sun Dec 03, 2017 8:34 pm by GDZone

» What is the standard garage door size?
Wed Nov 29, 2017 9:40 am by brooklynnygarage

» How do you change a garage door spring?
Mon Nov 27, 2017 6:36 am by queensgarage

» How to choose a garage door?
Mon Nov 27, 2017 6:31 am by njoverheadgaragedoors

Buy Marantec Remotes

Buy Raynor Remotes

Buy Raynor Remotes

Counter


    new transmitter won't open door

    Share

    fred46

    Posts : 1
    Join date : 2011-07-06

    new transmitter won't open door

    Post  fred46 on Wed Jul 06, 2011 4:29 pm

    I have a MacDelux 2005 garage door opener. Lost a transmitter and purchased a Marantec 315MHz external receiver kit. Hooked it up following directions supplied with the correct wires in terminals 3 & 4. Pressed programming button & LED flashed. Pressed transmitter button & LED flashed as long as transmitter button was depressed. When I released button the light went out. It never burned continuously for 4 sec. Also tried following coding instructions in Mac Lift owner's manual. In both instances when I pressed transmitter button, I heard a click in the power plug radio control, the LED blinked continuously & the door didn't budge. I can still operate the door from the wall transmitter. Any idea what I'm doing wrong.

    fred46
    avatar
    GDZone
    Admin

    Posts : 225
    Join date : 2009-04-28

    Re: new transmitter won't open door

    Post  GDZone on Thu Jul 07, 2011 12:46 pm

    "Pressed programming button & LED flashed"...I'm assuming you pressed & released the oval program button on the Plug-in Receiver & the yellow program button was flashing......if that's what you did then the next step is to press & HOLD the remote button until the program button light goes out (don't release remote button until light on receiver goes out).

    "In both instances when I pressed transmitter button, I heard a click in the power plug radio control"....if you press the remote button & the Plug-in Receiver makes a clicking noise then the remote is programmed to the radio receiver. If that's the case then the problem will be in the wiring. Either the two wires aren't pushed far enough into #3 & #4 terminal on the opener or they aren't inserted far enough into the Plug-in Receiver to make contact....check over the connections on both ends.

    jayzenony

    Posts : 79
    Join date : 2016-11-09
    Age : 22
    Location : new yourk

    garage door company in New York

    Post  jayzenony on Thu Nov 24, 2016 5:04 pm

    we are the garage door company in New York, that repair your garage door please visit http://www.garagedoorsnewyork.com/
    Attachments
    Garage Door Company New York.docx
    You don't have permission to download attachments.
    (12 Kb) Downloaded 1 times
    avatar
    njoverheadgaragedoors

    Posts : 49
    Join date : 2017-03-21

    Re: new transmitter won't open door

    Post  njoverheadgaragedoors on Tue Mar 28, 2017 4:01 am

    you shuld replace your transmitter.

    Sponsored content

    Re: new transmitter won't open door

    Post  Sponsored content


      Current date/time is Sun Dec 17, 2017 6:46 am