Questions & discussions of garage door operator problems and solutions.

Latest topics

» Seal your garage door
Today at 3:00 am by brooklynnygarage

» Pole Barn Door Opener
Sat Aug 19, 2017 12:13 pm by OldBlue

» need to get garage door open
Sat Aug 19, 2017 7:11 am by benchbella

» advise on garage repair in phoenix az
Fri Aug 18, 2017 11:02 am by sandykiwi66

» Garage door not opening.
Fri Aug 18, 2017 11:00 am by sandykiwi66

» What is the best garage door for all homes?
Fri Aug 18, 2017 10:57 am by sandykiwi66

» Welcome To The Forums
Mon Aug 14, 2017 6:55 am by queensgarage

» What goes into the cost of a commercial garage door?
Mon Aug 14, 2017 6:50 am by queensgarage

» What type of spring is better...extension or torsion?
Mon Aug 14, 2017 5:04 am by njoverheadgaragedoors

Buy Marantec Remotes

Buy Raynor Remotes

Buy Raynor Remotes

Counter


    Erasing Codes from a 500RGD on a 170-8

    Share

    Chad in UT

    Posts : 3
    Join date : 2014-04-10

    Erasing Codes from a 500RGD on a 170-8

    Post  Chad in UT on Thu Apr 10, 2014 7:09 pm

    We just purchased a older home and we only received one garage door remote.  So before I purchase new remotes I would like to delete all of the old remotes that the previous owners still might have in their possession.  There is also a older keypad on the front that runs off of a 12v battery, that I would like to erase as well.

    There are 3 garage door openers (170-8) each with a 500rgd.

    I have tried to hold down the learn button for like 30 seconds and that doesn't seem to work.  Tried unplugging and replugging. Tried to push both buttons at once. I am at a loss. I can't find any manuals online for the 500RGD.  Any help is appreciated.

    Thanks in advance.

    Chad
    avatar
    GDZone
    Admin

    Posts : 208
    Join date : 2009-04-28

    Re: Erasing Codes from a 500RGD on a 170-8

    Post  GDZone on Fri Apr 11, 2014 11:32 am

    Hi Chad - what model of remote do you have? The model will be printed on the back of the remote if it hasn't worn off.

    Chad in UT

    Posts : 3
    Join date : 2014-04-10

    Re: Erasing Codes from a 500RGD on a 170-8

    Post  Chad in UT on Fri Apr 11, 2014 1:50 pm

    Admin wrote:Hi Chad - what model of remote do you have? The model will be printed on the back of the remote if it hasn't worn off.

    The one remote that I was given is a 63LM.  When I open up the battery door it has dip switches and some sort of a red button.

    Here is a pic of one of the three receivers that I am trying to clear
    avatar
    GDZone
    Admin

    Posts : 208
    Join date : 2009-04-28

    Re: Erasing Codes from a 500RGD on a 170-8

    Post  GDZone on Fri Apr 11, 2014 3:03 pm

    To reprogram your remote to your three operators with a new code you'll need to do the following:

    1. Open the battery compartment on the remote. Move switches #2 thru #9 to whatever you want.

    2. Slide #1 dip switch to up position. Go to the 1st opener & press the white program button. Now press the 1st remote button. That operator should now be programmed.

    3. Slide #1 dip switch to middle position. Go to 2nd opener & press the white program button. Now press the 2nd remote button. That operator should now be programmed.

    4. Do the same for the 3rd button by programming it with the #1 dip switch in the bottom position.

    Your remote should now be programmed to all three operators with a new code. Any old remotes will no longer work.

    Hope this helps.

    Chad in UT

    Posts : 3
    Join date : 2014-04-10

    Re: Erasing Codes from a 500RGD on a 170-8

    Post  Chad in UT on Fri Apr 11, 2014 3:09 pm

    Thank you! I am going to give it a try right now.  Now I need to order some new remotes from you.  Thanks again.

    Chad

    Update: It worked like a charm. I don't have more of the old remotes to test but it programed this one, so I assume that it did as you said and deactivated the others. Thanks again.
    avatar
    GDZone
    Admin

    Posts : 208
    Join date : 2009-04-28

    Re: Erasing Codes from a 500RGD on a 170-8

    Post  GDZone on Fri Apr 11, 2014 3:44 pm

    I'm glad we could help. Here's a link to the 63LM Remotewhich is the same as what you have.
    avatar
    brooklynnygarage

    Posts : 52
    Join date : 2016-11-22
    Age : 27
    Location : 23 Bleecker ST Brooklyn, NY-11221

    Re: Erasing Codes from a 500RGD on a 170-8

    Post  brooklynnygarage on Fri May 05, 2017 9:14 am

    Please share your steps behind this process.

    Sponsored content

    Re: Erasing Codes from a 500RGD on a 170-8

    Post  Sponsored content


      Current date/time is Mon Aug 21, 2017 3:20 am