Questions & discussions of garage door operator problems and solutions.

Buy Marantec Remotes

Buy Raynor Remotes

Buy Raynor Remotes

Counter


    Raynor 1/3 HP Model 110-7

    Share

    MTL

    Posts : 1
    Join date : 2015-08-08

    Raynor 1/3 HP Model 110-7

    Post  MTL on Sat Aug 08, 2015 4:10 pm

    I have an old raynor 110-7 model and my one button wall unit was working intermittently. I took it apart to check connections but was unable to reassemble properly. Is there any where I can get assembly schematic for the one button wall mount? It appears to be simple enough, just a spring and a copper cap, but I'm unable to get this to work again. Any help is appreciated.
    avatar
    GDZone
    Admin

    Posts : 216
    Join date : 2009-04-28

    Re: Raynor 1/3 HP Model 110-7

    Post  GDZone on Sun Aug 09, 2015 1:55 am

    You would be better off just replacing the button. You can find the button here or just use any non-illuminated doorbell button.


    _________________
    Brian

    Garage Door Zone

    Visit GarageDoorZone.com
    Like Us On Facebook
    Join Us On Twitter
    Sign Up For Our Newsletter

    Bob Gilmore

    Posts : 2
    Join date : 2016-11-12

    Re: Raynor 1/3 HP Model 110-7

    Post  Bob Gilmore on Sat Nov 12, 2016 3:02 pm

    I have a Raynor M-170-7. Always worked perfect. Recently opened it ok, when pushed button to close nothing. Unit has power but noticed sender sensor has green light, receiver sensor has NO LIGHT.
    Do the sensors go bad? All wire connections appear OK.
    avatar
    GDZone
    Admin

    Posts : 216
    Join date : 2009-04-28

    Re: Raynor 1/3 HP Model 110-7

    Post  GDZone on Sat Nov 12, 2016 5:35 pm

    Yes the sensors can go bad. Unfortunately the R170 openers usually used the PEC-R4 sensors which are no longer available and there are no replacements available. Look at the wires coming out of each sensor - if there's 2 wires coming out of each sensor then you have the PEC-R4 sensors.


    _________________
    Brian

    Garage Door Zone

    Visit GarageDoorZone.com
    Like Us On Facebook
    Join Us On Twitter
    Sign Up For Our Newsletter

    Bob Gilmore

    Posts : 2
    Join date : 2016-11-12

    Re: Raynor 1/3 HP Model 110-7

    Post  Bob Gilmore on Sat Nov 12, 2016 9:45 pm

    I have PEC-R3 sensors. Is there a replacement?
    Also, would a bad sensor cause the motor and whole unit not to operate?
    avatar
    GDZone
    Admin

    Posts : 216
    Join date : 2009-04-28

    Re: Raynor 1/3 HP Model 110-7

    Post  GDZone on Sun Nov 13, 2016 11:35 am

    The operator should open the door if you press and release the wall button but if you have to hold your finger on the wall button to close the door then the the sensors are bad (or out of adjustment). The original PEC-R3 sensors are no longer available but there are replacements available here. You'll have to install new mounting brackets (which are included) but the wire plugs on the ends are the same and will plug into the existing wires.


    _________________
    Brian

    Garage Door Zone

    Visit GarageDoorZone.com
    Like Us On Facebook
    Join Us On Twitter
    Sign Up For Our Newsletter
    avatar
    brooklynnygarage

    Posts : 57
    Join date : 2016-11-22
    Age : 27
    Location : 23 Bleecker ST Brooklyn, NY-11221

    Re: Raynor 1/3 HP Model 110-7

    Post  brooklynnygarage on Wed Apr 19, 2017 4:57 am

    This model is easy to install. garage door service brooklyn.

    Sponsored content

    Re: Raynor 1/3 HP Model 110-7

    Post  Sponsored content


      Current date/time is Sat Oct 21, 2017 2:02 am